Roof Flashings for Metal Roofs

Oatey® invented the flashing industry more than 100 years ago. Today Oatey Flashings are used in commercial and residential applications where a water-tight seal around plumbing vent pipe or outside wall penetrations is required. Oatey Master Flash® Roof Flashings are engineered for metal roof applications for any pitch. Easily customized to accommodate a broad range of pipe diameters.
* MASTER FLASH® is a Registered Trademark of the Aztec Washer Company, Inc.

loading...
Filter by
Product Type
Showing 3 of 3
038753140568_H_001.jpg - Closed to 1/4 to 3/4 in. Master Flash® EPDM roof flashing 4-1/2 in. x 4-1/2 in. Base

Oatey® Master Flash® Roof Flashings

Black

Plastic

Oatey

Master

For any panel configuration, roof pitch or pipe location

Molds to all types of roofing surfaces, including metal, plastic, tile and rubber membrane

Marked cut lines allow for easy installation and customization for various pipe sizes with a sharp knife or scissors

No

Rated to withstand 212°F continuous heat and approved for Type B installations; intermittent temperature resistance to 275°F

Non-fading EPDM collar provides maximum resistance to weathering caused by ozone and UV rays

Slide over pipe, use silicone sealant between base and surface, then secure with sheet metal screws

MASTER FLASH® is a Registered Trademark of the Aztec Washer Company

0.25 in. - 2 in.

0.15 lb.

4.5" X 4.5"

Closed to 1/4 in.–3/4 in. Master Flash® EPDM roof flashing

4-1/2 in. x 4-1/2 in. soft aluminum base for profiled metal roofs

0.25 in. - 4 in.

0.45 lb.

8" X 8"

Closed to 5-3/4 in. Master Flash® EPDM roof flashing

8 in. x 8 in. soft aluminum base for profiled metal roofs

3 in. - 6 in.

0.75 lb.

10" X 10"

Closed to 2-3/4 in.–7 in. Master Flash® EPDM roof flashing

10 in. x 10 in. soft aluminum base for profiled metal roofs

5 in. - 9 in.

1.2 lb.

12" X 12"

Closed to 4-3/4 in.–10 in. Master Flash® EPDM roof flashing

12 in. x 12 in. soft aluminum base for profiled metal roofs

4 in. - 8.25 in.

0.9 lb.

11" X 11"

Closed to 4 in.–8-1/4 in. Master Flash® EPDM roof flashing

11 in. x 11 in. soft aluminum base for profiled metal roofs

6 in. - 11 in.

1.5 lb.

14" X 14"

Closed to 5-1/2 in.–11-1/2 in. Master Flash® EPDM roof flashing

14 in. x 14 in. soft aluminum base for profiled metal roofs

7 in. - 13 in.

2.2 lb.

17 x 17 in

Closed to 6-3/4 in.–13-1/2 in. Master Flash® EPDM roof flashing

17 in. x 17 in. soft aluminum base for profiled metal roofs

1.25 in. - 3 in.

0.3 lb.

6" X 6"

Closed to 7/8 in.–4 in. Master Flash® EPDM roof flashing

6 in. x 6 in. soft aluminum base for profiled metal roofs

10 in. - 18 in.

2.95 lb.

25 x 25 in

Closed to 8 in.–20-1/2 in. Master Flash® EPDM roof flashing

25 in. x 25 in. soft aluminum base for profiled metal roofs

There are no results available

Helpful Resources


Videos

How to Select Roof Flashings

How to Install a Roof Flashing

FAQs