Oatey Set-Rite® Toilet Flange Extension Kit is a watertight solution for raising the toilet flange during a remodel. This extension kit provides the ability to easily extend the flange surface above the finished floor for optimum sealing with a standard wax ring. The kit includes four different size spacers and six self tapping screws to complete the installation. Oatey products have earned the trust of plumbing professionals for over 100 years.
Part #: 43400
Key Features & Benefits
- Set-Rite® kit extends toilet flange surface above finished floor
- Corrects improper flange height during repairs and remodels
- For existing PVC, ABS, cast iron or stainless steel ringed flange
- Creates optimum sealing with a standard wax ring
- Corrects flange height from 1/4 in. to 1-5/8 in.
- Includes 4 sized spacers that can be combined to meet desired height
- Foam rubber gasket seals the spacers to the new flange
- Includes 6 recessed screw holes to secure the flange to the floor
- Includes (6) 3.5 in. self tapping screws
- UPC listed solution
Technical Resources (4)
Available in 6 variations
Frequently Asked Questions
After the toilet has been removed, you must remove the existing toilet bolts and clean all the old wax off the existing toilet flange. Decide how much height is needed in order for the bottom of the top flange to be parallel with the finished floor height. You should replace the existing flange if it is broken or rusted badly; the spacer kit will not work for this application. After confirming the existing flange is in good condition, install the new extra-long toilet bolts into the flange. You can use the gaskets that come with the kit to seal between multiple PVC spacers, but 100% silicone is recommended between the top of the existing flange and the bottom of the first spacer. This will ensure that all voided areas are water tight between the transition points. After the desired height is reached, the flat washers and 1/4" nuts are threaded onto the extra-long bolts. This will compress and hold the spacers in place. It is recommended that you try and secure the new spacer or spacers to the subfloor through the four holes molded into the spacers. You can now install a wax seal and finish the toilet installation. Never use one of the seals in place of the wax seal. THE TOILET WILL LEAK WHEN FLUSHED!
Is there a flange that can be used to replace a broken or corroded cast iron flange for a toilet?
Oatey offers three styles of repair flanges for this application. The first is the No-Caulk cast iron repair flange which comes in two depths. Once the old flange is removed and cast iron pipe is cleaned off, these flanges will slide over the vertical cast iron drain pipe. The flat side of the gasket should be facing down and resting on the inside bottom lip of the flange. Tightening the four bolts in even rotation will compress the gasket against the outside of the pipe, and create a water tight seal. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. The second is our PVC or ABS Twist-N-Set repair flange which inserts into the vertical cast iron drain pipe after the old flange is removed. The gasket tightens as the flange is turned in a clockwise rotation. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. The third option is the PVC or ABS Replacement closet repair flange which also inserts into the vertical cast iron drain pipe after the old flange is removed. This flange is sealed by the tightening of three stainless steel bolts in even rotation. This compresses the gasket between the outside of the flange tail piece, and the inside of the cast iron drain. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. All flanges must be screwed into the subfloor before setting the toilet bowl into place, this sometimes will require drilling pilot holes through the finished flooring.
Do the flanges create a water tight seal around the pipe and hole that the pipe passes through?
No. The flanges are strictly cosmetic. If the penetration in the finished surface needs to be watertight, you will need to use an approved silicone product for application.