Oatey® Level Fit Closet Flange with stainless steel ring sits flush on the floor and quickly and easily connects a water closet outlet to a plumbing system. Stainless steel rings have a bolt slot shelf to stabilize bolts during installation. Oatey products have earned the trust of plumbing professionals for over 100 years.
- Solvent welds inside of 4 in. or over 3 in. ABS Sch. 40 DWV pipe
- 1.42 in. offset allows a margin of error for drain pipe/toilet flange alignmentll Durable metal ringll ABS plasticll6 mounting locations
- UPC Listed
- Metal ring can be rotated to allow precise alignment of bolts and screws
- 6 screw holes to secure flange to the floor
- UPC and ASTM D2661 listed
- For warranty product details, refer to the Oatey Limited Warranty document
|Pipe Size:||3 or 4 in.|
|Connection Type:||Solvent Weld|
Available in 3 Variations
Showing 3 of 3
There are no results available
After the toilet has been removed, you must remove the existing toilet bolts and clean all the old wax off the existing toilet flange. Decide how much height is needed in order for the bottom of the top flange to be parallel with the finished floor height. You should replace the existing flange if it is broken or rusted badly; the spacer kit will not work for this application. After confirming the existing flange is in good condition, install the new extra-long toilet bolts into the flange. You can use the gaskets that come with the kit to seal between multiple PVC spacers, but 100% silicone is recommended between the top of the existing flange and the bottom of the first spacer. This will ensure that all voided areas are water tight between the transition points. After the desired height is reached, the flat washers and 1/4" nuts are threaded onto the extra-long bolts. This will compress and hold the spacers in place. It is recommended that you try and secure the new spacer or spacers to the subfloor through the four holes molded into the spacers. You can now install a wax seal and finish the toilet installation. Never use one of the seals in place of the wax seal. THE TOILET WILL LEAK WHEN FLUSHED!
Is there a flange that can be used to replace a broken or corroded cast iron flange for a toilet?
Oatey offers three styles of repair flanges for this application. The first is the No-Caulk cast iron repair flange which comes in two depths. Once the old flange is removed and cast iron pipe is cleaned off, these flanges will slide over the vertical cast iron drain pipe. The flat side of the gasket should be facing down and resting on the inside bottom lip of the flange. Tightening the four bolts in even rotation will compress the gasket against the outside of the pipe, and create a water tight seal. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. The second is our PVC or ABS Twist-N-Set repair flange which inserts into the vertical cast iron drain pipe after the old flange is removed. The gasket tightens as the flange is turned in a clockwise rotation. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. The third option is the PVC or ABS Replacement closet repair flange which also inserts into the vertical cast iron drain pipe after the old flange is removed. This flange is sealed by the tightening of three stainless steel bolts in even rotation. This compresses the gasket between the outside of the flange tail piece, and the inside of the cast iron drain. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. All flanges must be screwed into the subfloor before setting the toilet bowl into place, this sometimes will require drilling pilot holes through the finished flooring.
When would a Closet Flange Spacer Kit be used?
The Closet Flange Spacer Kit is used when the finished floor of your bathroom is higher than the bottom of the existing toilet flange.