Oatey® ABS Offset Closet Flange with Stainless Steel Ring
Oatey® Level Fit™ Offset Closet Flange includes a stainless steel ring that provides added strength and cracking resistance to the flange. Rotate the metal ring with 360° swivel, providing adjustability and precise alignment of bolts and screws. Oatey products have earned the trust of plumbing professionals for over 100 years.
Part #: 43606
Technical Resources (3)
Technical Resources (3)
- Level Fit™ offset toilet flange with stainless steel ring
- Solvent welds inside of 4 in. or over 3 in. ABS Sch. 40 DWV pipe
- 360° rotation allows wide range of connections in tight spaces
- 1-1/2 in. offset allows a margin of error for drainpipe/toilet flange alignment
- Rotate metal ring to allow precise alignment of bolts and screws
- Made of ABS plastic with durable metal ring
- 6 mounting locations and screw holes to secure flange to the floor
- UPC and ASTM D2661 listed
- For warranty product details, refer to the Oatey Limited Warranty document
|Pipe Size:||3 in. x 4 in.|
|Connection Type:||Solvent Weld|
|Ring Material:||Stainless Steel|
After the toilet has been removed, you must remove the existing toilet bolts and clean all the old wax off the existing toilet flange. Decide how much height is needed in order for the bottom of the top flange to be parallel with the finished floor height. You should replace the existing flange if it is broken or rusted badly; the spacer kit will not work for this application. After confirming the existing flange is in good condition, install the new extra-long toilet bolts into the flange. You can use the gaskets that come with the kit to seal between multiple PVC spacers, but 100% silicone is recommended between the top of the existing flange and the bottom of the first spacer. This will ensure that all voided areas are water tight between the transition points. After the desired height is reached, the flat washers and 1/4" nuts are threaded onto the extra-long bolts. This will compress and hold the spacers in place. It is recommended that you try and secure the new spacer or spacers to the subfloor through the four holes molded into the spacers. You can now install a wax seal and finish the toilet installation. Never use one of the seals in place of the wax seal. THE TOILET WILL LEAK WHEN FLUSHED!
Is there a flange that can be used to replace a broken or corroded cast iron flange for a toilet?
Oatey offers three styles of repair flanges for this application. The first is the No-Caulk cast iron repair flange which comes in two depths. Once the old flange is removed and cast iron pipe is cleaned off, these flanges will slide over the vertical cast iron drain pipe. The flat side of the gasket should be facing down and resting on the inside bottom lip of the flange. Tightening the four bolts in even rotation will compress the gasket against the outside of the pipe, and create a water tight seal. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. The second is our PVC or ABS Twist-N-Set repair flange which inserts into the vertical cast iron drain pipe after the old flange is removed. The gasket tightens as the flange is turned in a clockwise rotation. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. The third option is the PVC or ABS Replacement closet repair flange which also inserts into the vertical cast iron drain pipe after the old flange is removed. This flange is sealed by the tightening of three stainless steel bolts in even rotation. This compresses the gasket between the outside of the flange tail piece, and the inside of the cast iron drain. Remember that the bottom of the flange must be set on top of the finished flooring, and then screwed into the subfloor. All flanges must be screwed into the subfloor before setting the toilet bowl into place, this sometimes will require drilling pilot holes through the finished flooring.
Do the flanges create a water tight seal around the pipe and hole that the pipe passes through?
No. The flanges are strictly cosmetic. If the penetration in the finished surface needs to be watertight, you will need to use an approved silicone product for application.
It appears that you're using an unsupported browser.
If you are currently using Internet Explorer we recommend you switch to Edge or another supported browser to enjoy the best experience Oatey.com has to offer.